PDA

Visualizza Versione Completa : Test TPS



Moli
10-24-2005, 10:11 PM
:( Ho testato il tps ome suggerito da beppe (con spilli e ditale rubati alla vecchia).
Dall'alto verso il basso i tre cavetti sono nero, blu e grigio.
Tra grigio e nero ci sono 5v. Tra grigio e blu 3,5v. Tra nero e blu ci sono 0,5 al minimo e 3,8v a tavoletta.
[?] Il problema è che il motore si mette in moto e funziona (male: cioè accelero e fa bouuuuu-wrumm) sia con il connettore inserito che disinserito!!!???
Non è che per caso il problema possa essere imputabile al MAS (mass air flow) che è sotto al corpo farfallato?

[8)][8)] In un sito ho trovato queste tabelle sono attendibili?

Engine Coolant Temperature Sensor.Front of engine, below Throttle Body. 185 Ohms @ 210F, 3400 Ohms @ 68F, 7,500 Ohms @ 39 F.

Engine Oil Temperature Sensor. Left rear of engine, just above the oil filter. 185 Ohms @ 210 F, 3400 Ohms @ 68 F, 7,500 Ohm @39 F.

Oil Pressure Sender/Switch. Top, left hand rear of engine. 1 Ohms @ 0 PSI, 43 Ohms @ 30 PSI, 86 Ohms @ 6PSI.

Fuel Quantity Sender. Top of fuel tank, beneath filler pipe escutcheon panel. 0 Ohms @ Empty, 45 Ohms @ 1/2 Full, 90 Ohms @ Full.

MAT (Manifold Absolute Temperature Sensor). Underside of manifold air plenum at rear. 185 Ohms @ 210 F, 3400 Ohms @ 70 F, 15,000 Ohms @ 40 F.

Outside Temperature Sensor. Right side of engine, top right corner of radiator. 4400 Ohms @ 60 F, 2200 Ohms @ 85 F.

In Car Temp Temperature Sensor. Coupe: above left seat near interior courtesy light, Convertible: center of cargo compartment lid. 4400 Ohms @ 60 F, 2200 Ohms @ 85 F.

MAF (Mass Air Flow) Sensor. Front of engine ahead of throttle body. .4 Volts @ idle, 5 Volts @ Full Throttle.

Oxygen (O2) Sensor. Left side of engine, in exhaust pipe. .1 Volt Lean Mixture, .9 Volt Rich Mixture.

TPS (Throttle Position Sensor). Right side of throttle body at the front. .54 Volts Idle, ~ 5 Volts Full Throttle.

hi-fi69
10-24-2005, 11:12 PM
...ma hai fatto il test ALDL?
Che codici d'errore t dà?

Cmq sentiamo gli esperti ... :D:D:D

Christian GM
10-25-2005, 07:50 AM
I valori sono ad occhio coerenti, l'importante è controllarli nel posto giusto.
Ma, giusto per idea, dato che la macchina al minimo gira bene ma non prende i giri, non è che non riesce a scaricare? nel senso di catalizzattore o marmitta parzialmente ostruito?

Saluti

convertible90
10-25-2005, 09:51 AM
Moli.... a tavoletta dovrebbe essere circa 4 ma 3.8 sono abbastanza per segnalare che sei a tavoletta.
Piuttosto.... tu parli di MAS e poi dici che si tratta del mass air FLOW sensor..[?]
Il MA(F) NON è montato sui 91 !!!! sei sicuro che è un 91?? i 90 e 91 L98 hanno strategia speed density e funzionano con un MAP sensor (manifold absolute pressure).
In ogni caso il MAF se presente non è sotto il corpofarfallato (li a lato c'è l'IAC) ma è tra il filtro e il corpo farfallato e sta nella parte di tubo dritto.
Posta il Vin number e stabiliamo una volta per tutte l'anno.

Moli
10-25-2005, 11:34 AM
:DLa macchina è certamente un 91 anche se ora non ho sottomano il vin. Se beppe dice che il MAF non è montato sui 91 è certamente vero io l'ho solamente buttato li, mi scuso per la mia ignoranza è che sono un po' attapirato.
La macchina non è che non sale di giri ma prima di salire ritarda di uno due secondi con un forte "rumore di aspirazione". Tra i mille e tre mila gire rompe un poco poi gira regolare se la tengo a 4000 sta lì per un po' poi tende a scendere. Se invece dal minimo schiaccio a tavoletta borbotta come se volesse spegnersi.
Con una marcia inserita (è autom.) si muove al minimo se schiaccio non va borbotta e basta.
Inizio a pensare di essermela giocata definitivamente.

hi-fi69
10-25-2005, 11:39 AM
Nn fasciarti la testa prima del tempo! X tutte le cose esiste una cura breve o lunga! Vedrai che i ragazzi del forum t daranno 1 mano x fare tutte le prove da te richieste. ;)

convertible90
10-25-2005, 11:51 AM
Il Map sensor è collegato a una fonte di vacuum??

Christian GM
10-26-2005, 07:34 AM
Con il VIN si può vedere bene che modello è, che motore monta, i bollettini tecnici, gli schemi elettrici e schemi depressioni.
Senza di quello ragioniamo a vuoto.

PS insisto sullo scarico...

Saluti

Moli
10-28-2005, 10:26 AM
:DRingrazio per l'aiuto e l'incoraggiamento.
La macchina è a 30km da dove mi trovo. Nel weekend vado a fare ancora una qualche verifica e prendo nota del vin.
Tengo a precisare che mi sto improvvisando meccanico. Il test ALDL che è, che serve per farlo?

hi-fi69
10-28-2005, 12:01 PM
...leggi i vari post:
diagnostica centralina, codici d'errore, engine service soon, ecc ... troverai delle informazioni molto utili.

A presto e facci sapè! ;)

Moli
11-02-2005, 05:41 PM
Eccovi il cod. vin 1G1YY2387M5111994
Un'altra cosa: ho notato che il problema peggiora a macchina calda.

Moli
11-02-2005, 05:41 PM
Eccovi il cod. vin 1G1YY2387M5111994
Un'altra cosa: ho notato che il problema peggiora a macchina calda.

Christian GM
11-03-2005, 08:17 AM
Questi sono i dati generali del tuo mezzo;

Caratteristiche del veicolo

Identificazione del Veicolo
Veicolo: Chevrolet Corvette (1984-1996)
VIN:: 1G1YY2387M5111994
Modello Anno: 1991 (04/04/1991)
Descrizione modello
Modello: 1YY07 CORVETTE (WB 96) 2 DR PLAINBACK / HATCHBACK Data: 03/11/2005
Unità: Ora: 07.53.47
Serie: 1YY - CORVETTE (WB 96)
Stile della 07 - 2 DR PLAINBACK / HATCHBACK
carrozzeria:
Informazioni supplementari sul veicolo

Tipo Caratteristiche del veicolo

FABBRICATO IN U.S. BUILT
COSTRUTTORE GENERAL MOTORS, GENASYS L.C.
SERIE CORVETTE
CARROZZERIA 2 DOOR COUPE/SEDAN HATCHBACK/LIFTBACK 07, 08, 77, 87
RESTRIZIONI ACTIVE (MANUAL) BELTS WITH DRIVER INFLATABLE RESTRAINT
MOTORE 1.6L L4 LV4/ 5.7L V8 L98/ 4.5L V8 LQ6
STABILIMENTO BOWLING GREEN, KY


Fermo restando che sarebbe utile attaccare un tester e vedere se la centralina presenta guasti o meno, l'unico difetto riconosciuto da GM con le tue precise caratteristiche riguarda la pompa benzina; visto che dici che si accentua a caldo. Si può controllarne la pressione con un apposito manometro che normalmente qualsiasi autoriparatore possiede.

Se fosse così:
pompa benzina € 140.64 + IVA 25163463
guarnizione € 13.45 + IVA 25091503
filtro benz € 20.90 + IVA 25171792

materiale originale AC Delco, disponibile in GM Europe.

Vedi questo bollettino tecnico:

FUEL PUMP DRIVEABILITY ISSUE DIAGNOSTIC INFORMATION #92-227-6E - (Jun 4, 1992)
Subject: FUEL PUMP RELATED DRIVEABILITY ISSUES

Model and Year: 1991-92 CAMARO, CAVALIER, CORSICA, BERETTA, LUMINA ND CORVETTE 1992 C1, K1, L/M AND S/T TRUCKS 1992 LUMINA APV

ENGINE APPLICATIONS: SUBJECT:

Car VINs A, B, D, F, H, J, L, N, P, Fuel Pump Noise; Engine Hesitation, T, X,1, 3, 4, 8 Sag, Loss of Power; or No Start Truck VINs E, H, K, L, W, Z (Fuel Pump or Contaminated Fuel supply) VEHICLE/TRUCK APPLICATIONS:

1991-92 Model Year F, J, L, W, Y Cars 1992 Model Year C, K, L, M, S, T Trucks 1992 Model Year U Van

CONDITION:

--------- Customer may comment of fuel pump noise/whine and/or cold start stall; engine hesitation, sag, loss of power; or check engine light with codes 32 or 44. Condition(s) may be intermittent, but would typically be experienced in the first 5 minutes of engine/vehicle operation.

CAUSE:

----- Possible fuel starvation.

The following matrix is provided to help during diagnosis activities.

Diagnostic Aids:

1. Oxygen sensor reading biased toward lean when the engine Is under load.

2. Fuel pressure drops or does not increase by at least 5 psi when throttle moves from idle to part throttle.

3. Fuel integrator values steadily increasing under load.

4. Intermittent condition temporarily eased when accelerator pedal is released. Condition returns when accelerator pedal is reapplied.

5. Complete loss of fuel pressure.

CORRECTION:

---------- Use Section 6E3 of the appropriate service manual to diagnose possible fuel system related problems. The vehicle may need to be operated under a load while monitoring fuel pressure to detect the problem.

IMPORTANT: MAKE CERTAIN THE FUEL SYSTEM IS PERFORMING TO SPECIFICATIONS BEFORE OTHER ENGINE CONTROL SYSTEM COMPONENTS ARE SERVICED.

PROCEDURE:

--------- Follow procedures identified in the appropriate service manual or: for 1992 "J" vehicles specifically, see Dealer Service Bulletin No. 92-176-6C, dated April 1992; for electrical intermittents, see Dealer Service Bulletin No. 92-05-8A, 86-56 and 88-101-8A as well as Section 8A of the service manual and instruction in required tool J-38125 usage.

Figure 1

General Motors bulletins are intended for use by professional technicians, not a "do-it-yourselfer". They are written to inform those technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions and know-how to do a job properly and safely. If a condition is described, do not assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See a General Motors dealer servicing your brand of General Motors vehicle for information on whether your vehicle may benefit from the information.

Christian GM
11-03-2005, 08:17 AM
Questi sono i dati generali del tuo mezzo;

Caratteristiche del veicolo

Identificazione del Veicolo
Veicolo: Chevrolet Corvette (1984-1996)
VIN:: 1G1YY2387M5111994
Modello Anno: 1991 (04/04/1991)
Descrizione modello
Modello: 1YY07 CORVETTE (WB 96) 2 DR PLAINBACK / HATCHBACK Data: 03/11/2005
Unità: Ora: 07.53.47
Serie: 1YY - CORVETTE (WB 96)
Stile della 07 - 2 DR PLAINBACK / HATCHBACK
carrozzeria:
Informazioni supplementari sul veicolo

Tipo Caratteristiche del veicolo

FABBRICATO IN U.S. BUILT
COSTRUTTORE GENERAL MOTORS, GENASYS L.C.
SERIE CORVETTE
CARROZZERIA 2 DOOR COUPE/SEDAN HATCHBACK/LIFTBACK 07, 08, 77, 87
RESTRIZIONI ACTIVE (MANUAL) BELTS WITH DRIVER INFLATABLE RESTRAINT
MOTORE 1.6L L4 LV4/ 5.7L V8 L98/ 4.5L V8 LQ6
STABILIMENTO BOWLING GREEN, KY


Fermo restando che sarebbe utile attaccare un tester e vedere se la centralina presenta guasti o meno, l'unico difetto riconosciuto da GM con le tue precise caratteristiche riguarda la pompa benzina; visto che dici che si accentua a caldo. Si può controllarne la pressione con un apposito manometro che normalmente qualsiasi autoriparatore possiede.

Se fosse così:
pompa benzina € 140.64 + IVA 25163463
guarnizione € 13.45 + IVA 25091503
filtro benz € 20.90 + IVA 25171792

materiale originale AC Delco, disponibile in GM Europe.

Vedi questo bollettino tecnico:

FUEL PUMP DRIVEABILITY ISSUE DIAGNOSTIC INFORMATION #92-227-6E - (Jun 4, 1992)
Subject: FUEL PUMP RELATED DRIVEABILITY ISSUES

Model and Year: 1991-92 CAMARO, CAVALIER, CORSICA, BERETTA, LUMINA ND CORVETTE 1992 C1, K1, L/M AND S/T TRUCKS 1992 LUMINA APV

ENGINE APPLICATIONS: SUBJECT:

Car VINs A, B, D, F, H, J, L, N, P, Fuel Pump Noise; Engine Hesitation, T, X,1, 3, 4, 8 Sag, Loss of Power; or No Start Truck VINs E, H, K, L, W, Z (Fuel Pump or Contaminated Fuel supply) VEHICLE/TRUCK APPLICATIONS:

1991-92 Model Year F, J, L, W, Y Cars 1992 Model Year C, K, L, M, S, T Trucks 1992 Model Year U Van

CONDITION:

--------- Customer may comment of fuel pump noise/whine and/or cold start stall; engine hesitation, sag, loss of power; or check engine light with codes 32 or 44. Condition(s) may be intermittent, but would typically be experienced in the first 5 minutes of engine/vehicle operation.

CAUSE:

----- Possible fuel starvation.

The following matrix is provided to help during diagnosis activities.

Diagnostic Aids:

1. Oxygen sensor reading biased toward lean when the engine Is under load.

2. Fuel pressure drops or does not increase by at least 5 psi when throttle moves from idle to part throttle.

3. Fuel integrator values steadily increasing under load.

4. Intermittent condition temporarily eased when accelerator pedal is released. Condition returns when accelerator pedal is reapplied.

5. Complete loss of fuel pressure.

CORRECTION:

---------- Use Section 6E3 of the appropriate service manual to diagnose possible fuel system related problems. The vehicle may need to be operated under a load while monitoring fuel pressure to detect the problem.

IMPORTANT: MAKE CERTAIN THE FUEL SYSTEM IS PERFORMING TO SPECIFICATIONS BEFORE OTHER ENGINE CONTROL SYSTEM COMPONENTS ARE SERVICED.

PROCEDURE:

--------- Follow procedures identified in the appropriate service manual or: for 1992 "J" vehicles specifically, see Dealer Service Bulletin No. 92-176-6C, dated April 1992; for electrical intermittents, see Dealer Service Bulletin No. 92-05-8A, 86-56 and 88-101-8A as well as Section 8A of the service manual and instruction in required tool J-38125 usage.

Figure 1

General Motors bulletins are intended for use by professional technicians, not a "do-it-yourselfer". They are written to inform those technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions and know-how to do a job properly and safely. If a condition is described, do not assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See a General Motors dealer servicing your brand of General Motors vehicle for information on whether your vehicle may benefit from the information.

Moli
11-05-2005, 12:21 PM
[^]Grazie Christian. Ti rangrazio tantissimo per il tuo interessamento
Fare il test per la centralina non è semplicissimo in quanto qui in zona sembra che nessun meccanico lo abbia, per non dire la faccia che fanno quando glielo chiedo, forse a Pavia trovo qualcuno. Mal che vada te la porterò presso la tua officina purtroppo il mezzo non potrà venirci sulle sue ruote. Se vuoi venire tu (sai se maometto non va alla mantagna...) ti pago la trasferta e il pranzo in un buon ristorante sulle colline piacentine.
In ogni caso devo rimandare tutti questi lavori a gennaio in quanto ora sono incasinato con altro (vedi dentista che mi sta costando più di un v8 nuovo).
Prima di tutto il patatrak con il radiatore e problemi connessi la macchina ogni tanto dava "soon service" quando viaggiavo per un po'(30") a velocità costante. Se invece tiravo non si accendeva mai.
Quindi qualche problema latente deve sempre averlo avuto.
Ringrazio di nuovo te e tutti i ragazzi del forum.

Christian GM
11-05-2005, 12:48 PM
A Pavia c'è un concessionario ufficiale GM.
Non mi risulta però che lavori su vetture non ufficiali, dovresti chiedere. Purtroppo non li conosco personalmente per poterti aiutare.

Buona continuazione dal dentista:D